Посібник Defort DPW-2000-SC Мийка високого тиску

Посібник

11

GB

When the trigger is now pressed with the machine run-

ning, detergent will spray out with the water.

RECOMMENDED CLEANING PROCEDURE

Dissolve dirt by applying detergent with the fan jet to

the dry surface. On vertical surfaces, work from the

bottom upwards. Leave the detergent to act for 1 to

2 minutes, but do not allow to dry out. Apply the high

pressure jet, keeping the nozzle at least 30 cm (10 in.)

from the surface, working from the bottom upwards.

Avoid allowing the rinsing water to run on to unwashed

surfaces.

SHUTTING DOWN THE PRESSURE

WASHER

CAUTION! Never disconnect the high-pres-

sure hose from the machine while the system

is still pressurized.

Follow the correct procedure:

1. Turn off the pressure washer by using the switch on

the machine.

2. Unplug the unit from the power source.

3. Turn off the water supply at the tap.

4. Press the trigger of the gun to depressurize the sys-

tem.

5. Disconnect the supply hose to the machine

6. Wipe all surfaces of the unit with a damp clean

cloth.

7. Engage the safety lock.

TROUBLESHOOTING

1. When switched on, the machine will not start

working.

● Plug is not well connected or electric socket is

faulty.

- Check plug, socket and fuse.

● The mains voltage is lower than the minimum re-

quirement for start up.

Check that the mains voltage is adequate.

● The pump is stuck.

- Refer to after storage instructions. Switch off the

unit and let the motor cool.

● Thermal safety has tripped.

- Leave the lance open with water comingthrough.

2. Fluctuating pressure

● Pump sucking air

- Check that hoses and connections are airtight

● Valves dirty, worn out or stuck. Pump seals worn.

- Clean and replace or refer to dealer.

3. Water leaking from the pump

● Seals worn out

- Check and replace, or refer to dealer

4. The motor stops suddenly

● Thermal safety switch has tripped due to overheat-

ing.

- Check that the mains voltage corresponds to

specifi cations. An extension cable, which is too thin,

and tool long can cause a voltage drop and cause

the motor to overheat. Leave to cool down. Use

heavy duty extension cables.

● Screw the outlet pressure hose onto the machine

and ensure a good hand tight fi t.

● Connect the spray lance to the trigger by means of

the push in and twist bayonet fi tting.

Ensure that this connection has been performed

positively and the bayonet has located correctly. En-

sure the hose has no kinks in it.

4. USE

WATER SUPPLY

● Ensure that you have a suitable water supply to

feed

the pressure washer. Check that all connections are

tight and there are no leaks in the hose.

● The supply tap should be fully open (do not turn on

the pressure washer yet).

● Now depress the trigger (unlock trigger lock fi rst) to

let water pass through the unit and expel any air.

WARNING! This unit is to be used with a

coldwater source only!

ELECTRICAL CABLES

Ensure that all cables are damage free before connect-

ing to the power supply.

The electric supply connection shall be made by

a qualifi ed electrician. It is recommended that the

electric supply to this appliance should include either

a residual current device that will interrupt the supply if

the leakage current to earth exceeds 30 mA for 30 ms

or a device which will prove the earth circuit.

CAUTION! The machine may cause electri-

cal disturbances when starting. If the motor

stops and fails to restart, wait 10-30 minutes

before restarting. THERMAL CUTOUT

TRIPPED

CAUTION! The cleaner must only be used

with clean water; use of unfi ltered water or

corrosive chemicals will damage the cleaner.

● Turn the motor switch to the “0” position.

● Check that the electrical supply voltage and fre-

quency (Volts/Hz) correspond to those specifi ed on

the cleaner data plate.

● Plug in the pressure washer and turn the unit on with

the main switch .

ADJUSTING THE NOZZLE 3

Water may be sprayed out of the nozzle either linearly

or in a fan shape. Turn on the pressure fi rst, and then

adjust the nozzle.

The water inlet fi lter must be inspected regularly, so as

to avoid blockage and restriction of the water supply

to the pump.

USING THE DETERGENT BOTTLE

To enable supply of detergent from the bottle, remove

nozzle of the spray lance according to the arrow on the

Fig. 3a.

The detergent nozzle and tank attaches to the end

of the trigger assembly in the same way as the lance

does. Fill the detergent tank with liquid detergent.

Рейтинг

Детальніше про цей посібник

Ми розуміємо, що добре мати паперовий посібник для вашого Defort DPW-2000-SC Мийка високого тиску. Ви завжди можете завантажити посібник з нашого сайту та роздрукувати самостійно. Якщо ви бажаєте отримати оригінальний посібник, радимо зв’язатися з Defort. Вони можуть надати оригінальний посібник. Шукаєте інструкцію до свого Defort DPW-2000-SC Мийка високого тиску іншою мовою? Виберіть потрібну мову на нашій домашній сторінці та знайдіть номер моделі, щоб дізнатися, чи є вона у нас.

Технічні характеристики

Усі посібники для Defort Мийки високого тиску
Більше посібників для Мийки високого тиску

Часті запитання про Defort DPW-2000-SC Мийка високого тиску

Наша служба підтримки шукає корисну інформацію про товар і відповідає на поширені запитання. Якщо ви знайдете неточність у наших запитаннях та відповідях, повідомте нас про це, скориставшись контактною формою.

Супутні товари

Посібник

Defort DPW-1800-VAC Мийка високого тиску

Посібник

Defort DPW-1650 Мийка високого тиску

Посібник

Defort DPW-1850 Мийка високого тиску

Посібник

Michelin MPX 22EHDS Мийка високого тиску

Посібник

Kärcher HD 6/13 CX Мийка високого тиску

Посібник

Kärcher HDS 6/14-4 CX Мийка високого тиску

Посібник

Bosch UniversalAquatak 125 Мийка високого тиску

Посібник

Kärcher HD 7/18 C Plus Мийка високого тиску

Пов'язані категорії